Skip to main content

How can I lock the front panel buttons on IFP5550/IFP6550/ IFP7550/IFP8650?

Applied model: 1. Americas: IFP**50 - Gen 1, IFP**50 - Gen 2, IFP**50 - Gen 3.  2. Asia Pacific & Africa: IFP**50, IFP**50-2, IFP**50-3. 3. Europe: IFP**50, IFP**50-2EP, IFP**50-3EP. . Please refer either method below:   You will need to set combination key to “ON” at Debug menuàOther Settingà Combination key.   Then the font panel but...

How to disable IFP5550/6550/7550/8650 USB port?

Applied model 1. Americas: IFP**50 - Gen 1, IFP**50 - Gen 2, IFP**50 - Gen 3, IFP**70 2. Asia Pacific & Africa: IFP**50, IFP**50-2, IFP**50-3, IFP**70 3. Europe: IFP**50, IFP**50-2EP, IFP**50-3EP, IFP**70   Please use remote control to enter debug menu via pressing INPUT 9 9 1 in sequence, then go to Other Setting--àUSB Disk Enable a...

What to do when the touch function has no response on the ViewBoard?

If touch fails across all input sources, you can perform a system initialization using the [INIT TV] command in the Debug Menu. Steps: Enter Debug Menu: Using the table below, and press the corresponding buttons based on your model. Execute Initialization: Locate and select [INIT TV] from the pop-up menu. System Restart: The dev...

What's the difference in audio output when connected to S/PDIF OUT(COAX OUT/OPTICAL) and AUDIO OUT on IFP?

1. S/PDIF:       When connected via COAX OUT or OPTICAL port to an external amplifier, the output signal level is fixed.    With this connection, both built-in and external speakers will output audio.        You need to adjust volume on IFP speaker via IFP volume control button or remote control and adjust volume on external speaker by...

How can I remotely control IFP to power on and off(standby)?

You can remotely control IFP with RS232 cable or Lan cable by ViewSonic vController.   <Note> To power on via Lan may work by model wise and needs to set IFP standby mode to sleep. Please check specification and UG if it supports.

Is there any recommended slot-in PC which can support vPro and TPM?

VPC14-WP-x and VPC12-WP-x can support both Intel® vPro and TPM 2.0.

What to do if "No Signal" appears on the ViewBoard while connecting an external device (HDMI, USB-C, or PC)?

Step 1: Confirm correct input source on the ViewBoard (IFP) Press the [Input Source] button on the IFP remote or touch menu. Select the matching input (e.g., HDMI1 / USB-C / VGA). Wait 5–10 seconds for the screen to detect input. Step 2: Check your cable and connection type Try another HDMI, USB-C, or VGA cable. If using USB-C...

What should I do when there is no signal on the ViewBoard when connecting a long HDMI cable?

ps. This article is applied to IFP6552-1A/1B, IFP7552-1A/1B and IFP8652-1A/1B Please replace HDMI premium certificated cable. If still have problem, please follow below instructions to adjust settings on the Debug menu for better compatibility. 1.    Update firmware to the latest version (20221201 or later). 2.    Enter Debug Menu by p...

What is the USB Type-C specification and video streaming compatible device by IFP6570 and IFP8670?

ViewSonic’s IFP6570 and IFP8670 USB Type-C port supports the below specifications: 1. DP alt mode: supported with DP1.4 (4K@60hz) 2. Power delivery specification: 60W (5V3A、9V3A、12V3A、15V3A、20V3A) 3. USB data transfer rate specification: USB 2.0 (480 Mbps) Note: USB Type-C refers to the connector type, not the capability of...

Where do I find IFP50/30/70 series touch driver for Mac?

Please download the touch driver for Mac in below link or visit the product page on our website.    IFP 50-1/50 Gen 1: Download IFP 30: Download IFP 50-2/50-2 EP/50 Gen2/50-3/50-3A/50-3B/50-3 Gen 3/70: Download

ViewBoard Support

General Questions Interactive Display Technical Documents

General InquiriesContact Us

Contact Us directly if you’re unable to get the answers and solutions for your ViewSonic products.