Skip to main content

Does ViewSonic provide Linux drivers for monitors?

No dedicated driver is required. ViewSonic monitors follow VESA standards, allowing Linux to automatically recognize the display via EDID. Plug and Play: Simply connect your monitor; the Linux kernel will automatically detect the hardware. Adjust Display Settings: Navigate to your distribution's [Settings] > [Displays] to configur...

How to fix ghosting, shadowing, or double images on the screen?

Image artifacts are typically caused by signal degradation or interference. Bypass any docking stations and use high-quality certified cables. Bypass Adapters/Docks: Remove any [Docking Stations] or [Video Splitters]. Connect the monitor directly to your PC to test the image quality. Upgrade Cable Quality: For long-distance connections...

Should I install Windows 10 drivers for my monitor?

ViewSonic plug and play monitors do not require a proprietary Windows 10 driver to be installed.   Instead, Windows 10 will automatically read the EDID information stored in the monitor and install Generic PNP Monitor drivers to enable its full resolution capabilities.   The only difference is you will see monitor model name in Device Manag...

How to set power lock and menu lock?

On some monitors, there is a power button lock that locks the power and power button in the ON position.  There is also a menu lock feature which can lock and unlock the OSD (On-Screen Display) Menu.  Power Lock: To lock the Power Button press and hold both the [1] button and the down arrow button for 10 seconds.  OSD Lock: ...

What is "Low Input Lag" and which one should I choose?

Input lag means the time difference between when user controls PC and sees the response on monitor.      There is a trade-off to picture/video performance. If no particular demand, it is suggested to set it to off.

What should I do if vertical or horizontal lines appear on my monitor?

Identify whether it is a "Hardware Failure" or a "Signal Issue." The quickest way is to open the monitor's OSD menu to isolate the cause. Perform the OSD Test (Crucial): Press the monitor buttons to bring up the built-in menu. Lines appear OVER the menu: This indicates a hardware/panel failure. Proceed to step 5. Lines are NOT on t...

Why Your Monitor Mount Joint Might Be Stiff

The rotation axis of the Arm Hinge may feel tight or exhibit restricted movement. This is by design, as the axis incorporates a degree of resistance to help prevent the monitor from dropping, tilting, or moving unintentionally after installation. Before a monitor is installed or when the monitor’s weight is not applied, the rotation...

Which cable do I need to support a 144Hz refresh rate?

To achieve 144Hz, you must use the correct version of DisplayPort (DP) or HDMI based on your resolution. DP is the recommended interface for high refresh rates. Cable Requirement Table: Target Resolution Recommended Cable (or higher) Note 1080p (FHD) DisplayPort / HDMI 1.3 Supported by most modern cables 1440p (2K) DisplayPort 1.2 /...

How to setup and configure dual monitors?

Connect your cables, then use system shortcuts to choose between "Extend" or "Duplicate" modes and arrange the display order. Step-by-Step Instructions: 1. Fast Mode Switching (Windows) Press the Win + P shortcut. Select [Extend] to use both screens for different content (Recommended). Select [Duplicate] to show the same image on b...

Why can’t my monitor automatically detect a source?

The "Auto Detect" feature is disabled by default on many models. You must manually enable it within the OSD menu to allow the monitor to switch between active ports automatically. Step-by-Step Instructions: Press the physical button to call up the OSD Main Menu. Navigate to the [Input Select] section. Locate [Auto Detect] at the bo...

LED Monitor การซัพพอร์ต

General Questions ColorPro™ (VP series)

สอบถามข้อมูลทั่วไปติดต่อเรา

ติดต่อเรา โดยตรง หากคุณไม่พบคำตอบและวิธีแก้ปัญหาสำหรับผลิตภัณฑ์ ViewSonic ของคุณ